Revolvo SRB Split Plummer Block Bearings improve reliability for food processor

28/08/2014 09:37:07
Download Press Release
ImagesClick Image for 300dpi jpg fileRevolvo SRB Split Plummer Block Bearings improve reliability for food processorRevolvo SRB Split Plummer Block Bearings improve reliability for food processor

Dealing with a breakdown in any production process can cost precious time and money. But when the failure is due to a bearing which is difficult to access, and the production line is processing a seasonal vegetable, time becomes even more critical. For D'Arta, a food processing company based near Roeselare in Belgium, the latest stoppage persuaded the maintenance manager to call Revolvo in to investigate the cause and offer a solution.

For a company involved in the processing of seasonal vegetables, a breakdown due to bearing failure can lead to significant losses in production. This is especially true when there is restricted access to the bearings. D'Arta's investigation into the most recent failure on its spinach slicing machine found that over-greasing and water contamination of the existing plummer block bearing assemblies were to blame.

The slicing machine has a driven shaft which is supported by one fixed and one floating bearing at either end, each of which are housed in conventional plummer block housings. In the event of a bearing failure, the time taken to remove and replace the bearings was considerable. This situation required not only a more reliable bearing but also a much quicker method of inspecting and replacing the bearings and seals.

The meeting with Revolvo, which is renowned for its SRB split roller bearing designs, led to a demonstration of the latest Split Plummer Block Bearing, which incorporates the benefits of the SRB design into applications using conventional plummer block bearings. It was clear that the innovative design would drastically reduce the time to change a bearing, but it also allowed for greater heat expansion and a higher degree of axial movement.

The solution, suggested by Revolvo, saw the installation of four complete bearing assemblies, suitable for the 100mm shaft diameter of the slicing machine, complete with a Walker sprung garter-seal arrangement to prevent the ingress of water. As part of the project, Revolvo also carried out on-site training for the maintenance engineers to demonstrate the ease of assembly and maintenance, as well as assisting with the installation of the bearings and realignment of the motor and gearbox.

The compact SRB split plummer block bearings are fully interchangeable with standard SNL/SN/SD/SAF series plummer blocks, making them suitable for a larger range of applications. The design greatly reduces the time required to replace a bearing, which traditionally can involve significant disassembly of a machine to allow the removal of a standard plummer block with a solid bearing.

In addition, the ability to easily remove the upper section of the bearing makes for rapid visual inspection, which saves time and reduces the risk of unplanned downtime. Combined with the ability to compensate for a significant degree of shaft misalignment, which helps to promote a long service life, this revolutionary SRB bearing design can significantly reduce maintenance time and help improve the overall reliability of the application.

The performance of the new SRB bearings at D'Arta resulted in evidence of a payback period of less than 8 months, along with improved reliability, which ensured that additional units would be installed in other areas of the production facility. Six captive drives on a conveyor section were replaced along with a further three processing lines, which were still in the planning stage, were also specified with Revolvo SRB bearings.


Revolvo, the world's leading manufacturer of specialist bearings, designs and manufactures bespoke high performance bearings for demanding and safety critical applications, combining its expertise for both Revolvo branded ball and roller bearings, and SRB split roller bearings. With our range of STANDARD to CUSTOM designed products, we offer extensive experience, flexibility and the technology to meet the most demanding industry needs.

The image(s) distributed with this press release may only be used to accompany this copy, and are subject to copyright. Please contact DMA Europa if you wish to license the image for further use.

Editor Contact

DMA Europa Ltd. : David Bedford
Tel: +44 (0)1562 751436 Fax: +44 (0)1562 748315

Company Contact

Revolvo Ltd : Adrian Menzies
Tel: +44 (0) 1384-245370 Fax: +44 (0) 1384-245371

  [ Back ]  
About the DMA Group Click to Read More