New retrofit control valves can increase pneumatic system safety ratings to SIL1 and SIL2

26/10/2016 13:40:23
 
 
Download Press Release
English
ImagesClick Image for 300dpi jpg fileNew retrofit control valves can increase pneumatic system safety ratings to SIL1 and SIL2New retrofit control valves can increase pneumatic system safety ratings to SIL1 and SIL2

Industries with highly automated processes, such as food & beverage and pharmaceuticals face many challenges, especially in terms of maintaining a safe environment. As increased legislation continues to require higher standards, Bürkert Fluid Control Systems has developed a series of innovative safety valve solutions that can be retro-fitted to existing control systems or incorporated into new designs.

Increasing levels of automation in industrial processes has brought with it higher levels of safety and reliability. This has led to, amongst other things, the adoption of the European Union’s Machinery Directive, 2006/42/EC and a number of other new standards such as IEC 62061. Within both of these pieces of legislation are details of increased safety functions, known as Safety Integrity Levels (SIL) or Performance Levels (PL) that categorise control components and structures with regard to fault detection, redundancy and reliability.

Essentially, plant manufacturers and operators are required to assess the safety of their equipment and if necessary make improvements to bring it within compliance. One of the crucial aspects of this evaluation is the provision of emergency valves and stop procedures that prevent harm in the event of an employee intervening in a process.

Safety circuits have very specific requirements, especially in terms of wiring and redundancy of components. As a simple example, an emergency stop circuit should have two sets of contacts in the pushbutton, which should be hard-wired to a safety relay or safety PLC which in turn is hard-wired to contacts that stop the process. This sort of arrangement would be classified as PLc or SIL1, which would be suitable for low level risks.

If the plant risk assessment has identified a higher category for a particular process, then it will be necessary to improve the reliability of the safety circuit. This can be done by introducing additional redundancy, which in the example above would be the addition of a control valve that could shutdown the process in question in the event that the original contacts had failed.

Many automated processes use pneumatic valve islands, connected to PLCs, to maintain the production process and any safety related circuits are separate from the valve island. In the wake of the introduction of EN ISO 13849, Bürkert has created two new valve types that could be retro-fitted onto the valve island and used for a safety-related shut-off, thanks to the additional wiring which allows the valve to be connected directly to a safety relay.

This innovation enables plant managers to ensure their control structures meet the requirements for PLc or SIL1 with a compact solution and minimal changes to the circuit. The only addition to the control cabinet is the safety relay, if it was not already present, which keeps both costs and space to a minimum.

The second addition to the Bürkert range is the redundancy block Type MKRS which can be installed in more demanding applications that require a higher level of safety. The introduction of a redundancy valve block will enable PLc or SIL2 to be achieved, which can apply to many applications in the hygienic sector where clean-in-place (CIP) procedures are used.

For example, in processes where an inspection hatch can be opened for maintenance, it is essential that the process must be stopped if a cover is removed at an inappropriate time. Under normal circumstances the safety valve on the pneumatic valve island will stop the process, but in situations where there is an increased risk the redundancy block is positioned so that if the safety valve does not operate, then the process will be stopped by the Type MKRS valve.

Equally of use to process engineers designing new systems, this is a very compact solution that can also easily be integrated into an existing control system without affecting the process control programming. For designers and OEMs these new innovations from Bürkert offer excellent reliability and minimal impact on current designs while delivering increased safety levels without increasing the footprint of the control structure.

About BURKERT

Burkert Fluid Control Systems is one of the leading manufacturers of control and measuring systems for fluids and gases. The products have a wide variety of applications and are used by breweries and laboratories as well as in medical engineering and space technology. The company employs over 2,500 people and has a comprehensive network of branches in 36 countries world-wide.

The image(s) distributed with this press release may only be used to accompany this copy, and are subject to copyright. Please contact DMA Europa if you wish to license the image for further use.

Editor Contact

DMA Europa Ltd. : Brittany Kennan
Tel: +44 (0)1562 751436 Fax: +44 (0)1562 748315
Web: www.dmaeuropa.com
Email: brittany@dmaeuropa.com

Company Contact

Bürkert Fluid Control Systems : Kirsty Anderson
Tel: +44 (0)1285 648761 Fax: +44 (0)1285 648721
Web: www.burkert.co.uk
Email: kirsty.anderson@burkert.com

 
  [ Back ]  
About the DMA Group Click to Read More