Selecting the best tipping gear for safety and profitability

09/04/2018 11:25:16
 
 
Download Press release
English
ImagesClick Image for 300dpi jpg fileSelecting the best tipping gear for safety and profitability

Commercial vehicles haul vast quantities of minerals, grain and other bulk materials around the UK each year. The figure for aggregates alone is 60,000,000 tonnes, so the total number of vehicle movements and load discharges is huge. Tipping vehicles remain the most efficient and profitable method for ejecting loads – but only when specified correctly.

Edbro offers engineering support to body builders and end users to ensure that every cylinder is providing the best and safest performance.

Tipping vehicles are a common sight on roads in the UK and around the world. They provide an efficient way of transporting and discharging bulk materials. For the most part, these operations are completed safely; however, a poorly designed or equipped truck can compromise safe operations so operators should be sure that they are buying the right tool for the job.

It is therefore advisable that tipping gear on the vehicle is designed or selected by experts, such as the Edbro team of engineers, and specified with the intended application in mind.

The design of the tipping mechanism used by all tippers consists of a large, long stroke hydraulic cylinder, a power pack to drive it, and the necessary controls. There are many different types of cylinder available – Edbro alone has five different ranges, each available in many lengths, diameters, speeds, powers and with additional optional features.

Ideally a cylinder is robustly built to withstand the rigours of its working life. It will have the power and reach to lift its proposed loads, plus the speed to allow profitability to be maintained. When designing a tipper there are several elements to consider: calculating the power required, considering component positioning on the vehicle and ensuring safe operation.

The performance specification is calculated from the weight of the load and its balance either side of the tipper’s pivot point; height/angle tip required; and speed of actuation expected. With these figures confirmed, appropriate components can be identified from which the best fit for the vehicle can be selected.

Edbro points out that alongside these technical considerations there must be full awareness of operational safety issues. Obviously it is a vital part of the designer’s responsibility to indentify risks and minimise them. Edbro’s engineers have many years experience in designing efficient and safe systems, and work in teams where discussions are encouraged and alternative options always considered.

For instance, selected tipping speed could influence tipping safety when hauling certain materials. Sludge, slurry and other viscous materials may flow unevenly as they tip, resulting in imbalance if the trailer rises too quickly. Edbro will review the intended use and help specify the ideal tipping speed to compromise between efficiency and safety.

Following on from the considerations on safety, designers may be tempted to oversize tipping mechanisms so that they are comfortably able to cope with their load. However, one must remember the primary purpose of business - profit. Most tippers are used for road haulage, where maximum vehicle weight is strictly governed. Where a designer chooses to over-specify, they will compromise the kerb weight of the vehicle and reduce its payload and profitability per tip.

For Edbro, both safety and profitability are primary concerns, and the company works beyond other manufacturers’ safety standards. All cylinders are designed and specified with a 50% safety factor to ensure ‘belt and braces’ security, yet through attention to detail, application experience and careful design they remain industry leaders in terms of kerb weight and load carrying capacity.

An important caveat to the point about over specification is that in off-road applications - say in quarries, construction sites and scrap yards - different rules apply and heavier loads that wouldn’t be legal on UK roads may be commonplace. Here designers are likely to allow for over-specification to meet the unusual load requirements.

Edbro takes tipper safety and profitability seriously and to this end fully trains all relevant personnel, including the sales team. Edbro sales engineers understand how to pick the correct cylinder, but they are also backed up by the in-house applications team who check and double check every gear choice. They use specialist software to run tipper analyses that calculates buckling loads, safety factors, optimum operating speeds etc.

Usefully Edbro has a cylinder selection wizard on the technical area of its website (which can be accessed by all registered users) that aids in picking the best ram depending on the body dimensions, required tip angle, payload, etc.

Despite the heavy loads and extreme forces associated with the haulage industry, profitability is a matter of marginal gains and safety considerations can be measured in degrees. Identifying and fitting the best tipping cylinder for each job will facilitate profitable operations and improve safety for all concerned.

Picture Captions

Picture Caption 1: Usefully Edbro has a cylinder selection wizard on the technical area of its website (which can be accessed by all registered users) that aids in picking the best ram depending on the body dimensions, required tip angle, payload, etc.

About JOST:

JOST is a leading global producer and supplier of safety-critical systems to the truck and trailer industry. The Company offers branded, quality products clustered in three systems: Vehicle Interface (focusing on products required to operate a commercial vehicle combination of trucks and trailers such as fifth wheels and landing gears), Handling Solutions (including container technology and hydraulic cylinders products) and Maneuvering (focusing on truck and trailer axles and forced steering). As the number one supplier of fifth wheels and landing gears globally, JOST is the market leader for Vehicle Interface systems. JOST’s global leadership position is driven by the strength of its brands, by its long-standing client relationships serviced through its global distribution network as well as by its efficient and asset-light business model.

The Company’s core brands “JOST”, “Rockinger”, “TRIDEC” and “Edbro” are well-recognized in the industry and highly regarded for their quality and continuous innovation. With its global distribution network and production facilities in thirteen countries across five continents, JOST has direct access to all major truck and trailer manufacturers and relevant end customers. JOST currently employs about 2,700 members of staff worldwide.

The image(s) distributed with this press release may only be used to accompany this copy, and are subject to copyright. Please contact DMA Europa if you wish to license the image for further use.

Editor Contact

DMA Europa Ltd. : David Bedford
Tel: +44 (0)1562 751436 Fax: +44 (0)1562 748315
Web: www.dmaeuropa.com
Email: infoallenquiries@dmaeuropa.com

Company Contact

JOST UK Ltd. : Danny Broomfield, JOST UK Ltd.
Tel: + 44 (0) 1204 528888 Fax: + 44 (0) 1204 531957
Web: www.jostuk.co.uk
Email: danny.broomfield@jost-world.com

 
  [ Back ]  
About the DMA Group Click to Read More